How to Drain Your Water Heater: A Step-by-Step Guide 

Tank water heaters are a reliable way to provide a fast supply of hot water for your home. The addition of a storage tank ensures some hot water is always available. But over time, other substances may build up inside the storage tank. This could be sediment or mineral buildup coming from the main water line or an opening in the pipes. Whatever the culprit is, this buildup can reduce the efficiency of water heaters. In severe cases it can clog up drainage and could even cause premature failure. 

Thankfully, draining your water heater and removing sediment buildup is a relatively straightforward task. A certified plumber in Fort Lauderdale can handle the process, but you can also drain the tank yourself if you know what you’re doing. Either way, draining the tank now can help minimize the risk you’ll need premature water heater replacement. 

Before You Begin… 

Before you start draining the tank, you should shut off the cold water supply. The supply valve connects your water heater with the main water line. Unless you have access to a well (and you might need to drain the tank more often if you do), the water main delivers all the potable water your home uses. Keeping the valve shut will stop more water from reaching the tank, allowing you to completely drain it. 

You’ll also want to grab a rubber hose, like one you would use for yard work. The hose allows you to safely drain the water heater tank without spilling water in your garage, utility closet, attic or wherever the water heater is stored. Make sure you place the other end of the hose far away from your home to stop the water from flooding back inside. 

Finally, a screwdriver will help you loosen stubborn screws or valves. You shouldn’t need any more tools than this unless you discover a problem with the water heater or nearby piping. At that point, it may be best to call a certified plumber in Fort Lauderdale. 

Step 1: Shut Off the Water Heater 

After you’ve shut off the water supply, you can shut off the water heater itself. This will be on the thermostat for natural gas water heaters or with a breaker switch for electric models. The pilot setting on gas water heaters can continue to stay on during flushing, but electric models must be completely off. This is due to the heating elements electric water heaters have, which remain submerged. In an empty tank, they could quickly overheat. You should also find the model’s manual, as some water heaters must be completely full before the heating elements are started. 

Even after you’ve shut off the water heater, you’ll have to wait for the water stored in the tank to cool down. It could be hours before the water cools to a safe temperature, so it is often best to leave the rest of the process for the following day. 

Step 2: Connect the Hose to the Water Heater’s Drain Valve 

Tank water heaters are designed with a drain valve you can use to empty the storage tank. Once you’re certain the water supply is disconnected and the water heater itself is off, go ahead and find the drain valve. Some models may have it covered up. Make sure the hose is securely fastened to prevent spilling hot water near you and the water heater. 

Step 3: Open a Faucet or Other Hot Water Tap 

Your home’s plumbing takes advantage of pressure inside the piping to deliver a consistent flow of water from the main water line to the rest of the house. This pressure needs to be relieved before the hot water can actually exit the tank. By heading to the closest faucet or spigot, you’ll release the pressure inside the piping. All you have to do is open the hot water tap to relieve the pressure before returning to the water heater. 

Step 4: Release the Drain Valve 

Remember that this water might still have some residual heat. Open the drain valve and allow all the water to drain from the tank. This should pull sediment buildup out of the tank and away from your home. But some buildup may be stuck to the inside of the tank. Turning the cold water supply back on will help flush stubborn minerals and other substances from the tank. 

Keep repeating this step until the water appears clear of sediment or minerals. If the drain isn’t working because of a clog, a trained plumber is likely required. 

Step 5: Re-Shut the Valve Before Refilling the Water Heater 

If everything proceeds normally, you should be able to take care of most excess sediment hiding inside your water heater. Close the drain valve, disconnect the hose and open the water supply to get things working again. As the water heater tank begins to fill, return to the hot water tap you opened. Once cold water starts to flow, you know the pressure is back at appropriate levels. 

At this point, you can open the gas valve or flip the breaker switch back on. Like we mentioned before, don’t forget that some models may need to be entirely full before the water can be safely heated. Make sure you look through your manufacturer’s instructions before starting the process. 

Keep Your Water Heater Sediment-Free for Best Results 

Tank water heaters are still a great option for supplying your hot water needs. Draining the tank every 1-2 years will help flush sediment buildup and keep things running at maximum efficiency. If you think your water heater is past the point of efficient heating, consider looking for water heater replacement in Fort Lauderdale from a technician you trust.